|
|
Programmer XPROG :
The XPROG supports programming of Motorola 68HC05xx,
68HC08xx, 68HC11xx microcontrollers internal EEPROM and serial
EEPROM's - most used programmable device in car radios, automotive
computers (dashboards, AIRBAG, immobilizers), and industrial
products. All supported devices
Motorola microcontrollers (on-board
programming):
MC68HC11A8, MC68HC11E9, MC68HC711E9, MC68HC811E2,
MC68HC11E20, MC68HC11G5, MC68HC711G5, MC68HC11N4, MC68HC11F1,
MC68HC11PH8, MC68HC711PH8, MC68HC11PA8, MC68HC711PA8, MC68HC11K4,
MC68HC711K4, MC68HC11KA4, MC68HC711KA4, MC68HC11L6,
MC68HC711L6,MC68HC11P2, MC68HC11F1
MC68HC11PH8(0H30R Q=614kHz) , MC68HC11PH8(3D64J
Q=614kHz) , MC68HC11P2(0G10V Q=614kHz) , MC68HC11P2(1E53M Q=614kHz)
, MC68HC11P2(3E74J Q=614kHz) , MC68HC11EA9(2D47J) ,
MC68HC11EA9(1D47J) , MC68HC11EA9, MC68HC05B6/16/32,
MC68HC705B16/16N/32, MC68HC05X16/32,C68HC05B32 (new type from Audi
CHORUS),MC68HC05H12(0H57A) , MC68HC05E6(0G72G) , MC68HC05E6(0F82B) ,
MC68HC05X32(0D69J;1H52A) , MC68HC05X32(0D53J) , MC68HC08AZ32 ,
C68HC08AZ32(0J66D) , MC68HC08AS60 , MC68HC08AZ60 , MC68HC08AZ60A ,
Serial EEPROM:
AT93C46, AT93C46A, AT93C56, AT93C57, AT93C66,
AT59C11, AT59C12, AT59C13, CAT24C01, CAT24WC01, CAT24C02, CAT24WC02,
CAT24C04, CAT24WC04, CAT24C08, CAT24WC08, CAT24C16, CAT24WC16,
CAT24C32, CAT24WC32, CAT24C64, CAT24WC64, CAT64LC10, CAT64LC20,
CAT64LC30, CAT93C46, CAT93C46A, CAT93C56, CAT93C57, CAT93C66,
CAT93C66A, CAT93C86, 24C01A, 24LC01B, 24C02A, 24LC02B, 24C04A,
24LC04B, 24C08A, 24LC08B, 24C16A, 24LC16B, 24C32A, 24LC32B, 85C72,
85C82, 85C92, 93C06, 93C46, 93LCS46, 93LC46B, 93C56, 93LC56, 93C66,
93LC66, 93C76, 93LC76, 93C86, 93LC86, M6M80011P, M6M80021P,
M6M80041P, NM93C06, NM93C46, NM93C14, NM93C56, NM93CS56, NM93C66,
NM93CS66, NM93C86A, SDE2506, SDE2526, X24C00, X24C01, X2402, X2404,
X2408, X24164, X24165, X2444, X24C44.
Hardware Specifications :
Include high output current MPU.
External
output for on-board device programming via universal XPROG
connector..
Serial port interface (up to 115K baud) works on
(COM1, COM 2, COM3 or COM4).
Function Specifications:
File Load / Save, Read, Write, Verify, Checksum,
Security, Edit, Options Configuration.
Electrical Requirements:
Operating Voltage : +12-15V DC.
Power Consumption
: 50 mA.
|
|
Processor: |
INTEL Pentium 60MHz or faster (depends on
operating system) |
|
|
Memory (RAM) |
32MB (depends on operating system) |
|
|
Hard drive: |
5MB free space |
|
|
Communication: |
One free physical COM-port |
|
|
Operating system: |
Microsoft Windows 95/98 (Windows NT/ME/2000/XP is not
supported) |
| |
|
|
How to read/program supported devices via
universal XPROG connector, download the XPROG-m
manual.
NOTE: If XPROG software returns
error:
"This program is
not compatible with your hardware.
Please
contact with you supplier" , check that the
PIC EEPROM memory is programmed correctly.
Free downloads :
|
